=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2010.04.02 21:55:41 =~=~=~=~=~=~=~=~=~=~=~= Orion1 CPU = Low === BUFFALO LS-GL U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode USB 1: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1118 phy Marvell Serial ATA Adapter Integrated Sata device found Device 0: OK Model: SAMSUNG HD501LJ Firm: CR100-10 Ser#: S0Z4J1DPA00498 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Using device ide0, partition 1 Loading from block device ide device 0, partition 1: Name: hda1 Type: U-Boot File:/initrd.buffalo 4513613 bytes read Using device ide1, partition 1 ** Bad partition 1 ** Booting from Device 0 hit any key to switch tftp boot. Hit any key to stop autoboot: 2 1 0 Hit any key to stop autoboot: 3 2 1 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Device 0: OK Model: SAMSUNG HD501LJ Firm: CR100-10 Ser#: S0Z4J1DPA00498 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Using device ide0, partition 1 Loading from block device ide device 0, partition 1: Name: hda1 Type: U-Boot File:/uImage.buffalo 1809464 bytes read Using device ide1, partition 1 ** Bad partition 1 ** <> ## Booting image at 00100000 ... Image Name: Linux-2.6.16.16-arm1 Created: 2007-06-29 2:14:44 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1809400 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00800000 ... Image Name: initrd Created: 2007-07-09 0:06:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4513549 Bytes = 4.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL --- Uncompressing Linux..................................................................................................................... done, booting the kernel. Linux version 2.6.16.16-arm1 (root@develop) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #3 Fri Jun 29 11:14:38 JST 2007 CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 200000000, Tclk = 166664740 - Warning - This LSP release was tested only with U-Boot release 1.7.3 Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Built 1 zonelists Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 PID hash table entries: 1024 (order: 10, 16384 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 0MB 0MB 0MB = 128MB total Memory: 110548KB available (3169K code, 460K data, 108K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 15360K NET: Registered protocol family 16 FLASH boardId = 12 Flash bankwidth 1, base ff800000, size 400000 BUFFALO LS_GL FLASH size 4096[KB] Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL Detected Tclk 166664740 and SysClk 200000000 Marvell USB EHCI Host controller #0: c16f5e00 Marvell USB EHCI Host controller #1: c16f5c00 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub use IDMA acceleration in copy to/from user buffers. used channels 2 and 3 Done. cesadev_init(c0011314) mvCesaInit: sessions=640, queue=32, pSram=f0000000 Fast Floating Point Emulator V0.9 (c) Peter Teichmann. SGI XFS with large block numbers, no debug enabled Initializing Cryptographic API io scheduler noop registered (default) io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (0) 'eth0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter ** BUFFALO Disable Command Queuing Function [0 0] ** Vendor: SAMSUNG Model: HD501LJ Rev: CR10 Type: Direct-Access ANSI SCSI revision: 03 Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c1480ba0 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: drive cache: write back SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: drive cache: write back sda: sda1 sda2 sda4 < sda5 sda6 > sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 physmap flash device: 400000 at ff800000 >jedec_probe Found: SST 39LF020 phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available ehci_platform ehci_platform.4523: EHCI Platform Host Controller ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_platform ehci_platform.16781: EHCI Platform Host Controller ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2 ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). ---- in linuxrc --- Fri Apr 2 12:51:22 JST 2010 err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244) CheckDevices linuxrc:choose operation (timeout 4[s]) 1:RamRoot other:HddRoot ? -HddRoot- kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. ** has Updated Files ** proc /proc proc rw 0 0 sysfs /sys sysfs rw 0 0 Freeing init memory: 108K init started: BusyBox v1.1.1 (2007.05.10-05:06+0000) multi-call binary Starting pid 252, console /dev/ttyS0: '/etc/init.d/rcS' --- rcStart (initrd) --- mkdir: Cannot create directory `/sys': File exists ===== exec:checkroot.sh ===== chmod: /home: No such file or directory mkdir: Cannot create directory `/var/lock': File exists rm: /var/lock/perfmon: is a directory rm: /var/lock/printing: is a directory rm: /var/lock/subsys: is a directory Unable to handle swap header version 16777216 swapon: /dev/ls_disk1_5: Invalid argument create dir : /home create dir : /var/www ===== exec:create_devlink.sh ===== ===== exec:fwupdate.sh ===== umount: /boot: not mounted mkdir: Cannot create directory `/boot': File exists kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. exist [hddrootfs.buffalo.updated] fwupdate.sh:FW update start mkdir: Cannot create directory `/rootfs': File exists 1000+0 records in 1000+0 records out meta-data=/dev/ls_disk1_2 isize=256 agcount=8, agsize=96139 blks = sectsz=512 data = bsize=4096 blocks=769111, imaxpct=25 = sunit=0 swidth=0 blks, unwritten=1 naming =version 2 bsize=4096 log =internal log bsize=4096 blocks=2560, version=1 = sectsz=512 sunit=0 blks realtime =none extsz=65536 blocks=0, rtextents=0 format ls_disk1_2 success. XFS mounting filesystem sda2 uncompressing tar image... XFS mounting filesystem sda2 rm: cannot remove `/boot/hddrootfs.buffalo.updated.done': No such file or directory Starting pid 504, console /dev/ttyS0: '/etc/init.d/rcDown' Starting pid 599, console /dev/ttyS0: '/bin/umount' warning: can't open /etc/mtab: No such The system is going down NOW !! Sending SIGTERM to all processes. Sending SIGKILL to all processes. Please stand by while rebooting the system. Synchronizing SCSI cache for disk sda: Restarting system. . >miconCntl_Reboot >miconCntl_ShutdownWait Orion1 CPU = Low === BUFFALO LS-GL U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode USB 1: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1118 phy Marvell Serial ATA Adapter Integrated Sata device found Device 0: OK Model: SAMSUNG HD501LJ Firm: CR100-10 Ser#: S0Z4J1DPA00498 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Using device ide0, partition 1 Loading from block device ide device 0, partition 1: Name: hda1 Type: U-Boot File:/initrd.buffalo 4513613 bytes read Using device ide1, partition 1 ** Bad partition 1 ** Booting from Device 0 hit any key to switch tftp boot. Hit any key to stop autoboot: 2 1 0 Hit any key to stop autoboot: 3 2 1 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Device 0: OK Model: SAMSUNG HD501LJ Firm: CR100-10 Ser#: S0Z4J1DPA00498 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Using device ide0, partition 1 Loading from block device ide device 0, partition 1: Name: hda1 Type: U-Boot File:/uImage.buffalo 1809464 bytes read Using device ide1, partition 1 ** Bad partition 1 ** <> ## Booting image at 00100000 ... Image Name: Linux-2.6.16.16-arm1 Created: 2007-06-29 2:14:44 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1809400 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00800000 ... Image Name: initrd Created: 2007-07-09 0:06:04 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4513549 Bytes = 4.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL --- Uncompressing Linux..................................................................................................................... done, booting the kernel. Linux version 2.6.16.16-arm1 (root@develop) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #3 Fri Jun 29 11:14:38 JST 2007 CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 200000000, Tclk = 166664740 - Warning - This LSP release was tested only with U-Boot release 1.7.3 Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Built 1 zonelists Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 PID hash table entries: 1024 (order: 10, 16384 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 0MB 0MB 0MB = 128MB total Memory: 110548KB available (3169K code, 460K data, 108K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 15360K NET: Registered protocol family 16 FLASH boardId = 12 Flash bankwidth 1, base ff800000, size 400000 BUFFALO LS_GL FLASH size 4096[KB] Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL Detected Tclk 166664740 and SysClk 200000000 Marvell USB EHCI Host controller #0: c16f5e00 Marvell USB EHCI Host controller #1: c16f5c00 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub use IDMA acceleration in copy to/from user buffers. used channels 2 and 3 Done. cesadev_init(c0011314) mvCesaInit: sessions=640, queue=32, pSram=f0000000 Fast Floating Point Emulator V0.9 (c) Peter Teichmann. SGI XFS with large block numbers, no debug enabled Initializing Cryptographic API io scheduler noop registered (default) io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (0) 'eth0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter ** BUFFALO Disable Command Queuing Function [0 0] ** Vendor: SAMSUNG Model: HD501LJ Rev: CR10 Type: Direct-Access ANSI SCSI revision: 03 Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c1480ba0 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: drive cache: write back SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off SCSI device sda: drive cache: write back sda: sda1 sda2 sda4 < sda5 sda6 > sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 physmap flash device: 400000 at ff800000 >jedec_probe Found: SST 39LF020 phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available ehci_platform ehci_platform.4523: EHCI Platform Host Controller ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_platform ehci_platform.16781: EHCI Platform Host Controller ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2 ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). ---- in linuxrc --- Fri Apr 2 12:53:25 JST 2010 err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244) CheckDevices linuxrc:choose operation (timeout 4[s]) 1:RamRoot other:HddRoot ? -HddRoot- kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. XFS mounting filesystem sda2 PRODUCTID=0x00000009 PRODUCTID=0x00000009 KERNEL:2007/6/29 11:13:34 HDD:2007/7/12 9:17:25 KERNEL:2007/7/9 9:5:54 HDD:2007/7/12 9:17:25 -- CopyFromInitrdToHdd -- == fsck_disks == e2fsck 1.27 (8-Mar-2002) fsck.ext3: Filesystem has unsupported feature(s) (/dev/ls_disk1_1) e2fsck: Get a newer version of e2fsck! 4+0 records in 4+0 records out XFS mounting filesystem sda2 Phase 1 - find and verify superblock... Phase 2 - using internal log - zero log... - scan filesystem freespace and inode maps... - found root inode chunk Phase 3 - for each AG... - scan and clear agi unlinked lists... - process known inodes and perform inode discovery... - agno = 0 - agno = 1 - agno = 2 - agno = 3 - agno = 4 - agno = 5 - agno = 6 - agno = 7 - process newly discovered inodes... Phase 4 - check for duplicate blocks... - setting up duplicate extent list... - clear lost+found (if it exists) ... - check for inodes claiming duplicate blocks... - agno = 0 - agno = 1 - agno = 2 - agno = 3 - agno = 4 - agno = 5 - agno = 6 - agno = 7 Phase 5 - rebuild AG headers and trees... - reset superblock... Phase 6 - check inode connectivity... - resetting contents of realtime bitmap and summary inodes - ensuring existence of lost+found directory - traversing filesystem starting at / ... - traversal finished ... - traversing all unattached subtrees ... - traversals finished ... - moving disconnected inodes to lost+found ... Phase 7 - verify and correct link counts... done proc /proc proc rw 0 0 sysfs /sys sysfs rw 0 0 XFS mounting filesystem sda2 VFS: Mounted root (xfs filesystem). Trying to move old root to /initrd ... /initrd does not exist. Ignored. Unmounting old root Trying to free ramdisk memory ... okay Freeing init memory: 108K init started: BusyBox v1.1.1 (2007.05.10-05:06+0000) multi-call binary Starting pid 316, console /dev/ttyS0: '/etc/init.d/rcS' --- rcStart (hddroot) --- Fri Apr 2 12:53:35 JST 2010 ** step1 ** ===== exec:checkroot.sh ===== mount: /dev/pts already mounted or /dev/pts busy mount: according to mtab, devpts is already mounted on /dev/pts rm: /var/lock/perfmon: is a directory rm: /var/lock/printing: is a directory rm: /var/lock/subsys: is a directory Unable to handle swap header version 16777216 swapon: /dev/ls_disk1_5: Invalid argument create dir : /var/www ===== exec:create_devlink.sh ===== ===== exec:procps.sh ===== ===== exec:devpts.sh ===== ===== exec:sethostname.sh ===== configure files from Buffalo parameters. ===== exec:restore_config.sh ===== kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. /sbin/hotplug [block] Restore previous configuration files tar: /boot/conf_save.tgz: No such file or directory unzip fail. ** step2 ** ===== exec:networking.sh ===== create network files.. IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[] killall: dhcpcd: no process killed route: SIOC[ADD|DEL]RT: No such process Configuration network interface: lo eth0 requesting DHCP tout=30[s] networking.sh: dhcp requesting... DontDownIfaceeth0: link down alwaysFork eth0: link up<5>, full duplex<5>, speed 1 Gbps<5> sendto: count 6 sync 1 sendto: count 5 sync 0 sendto: count 6 sync 0 dhcpcd.exe: interface eth0 has been configured with new IP=192.168.0.68 GATEWAY=192.168.0.1 ** networking.sh dhcp fin. configure files from Buffalo parameters. ===== exec:syslog.sh ===== Starting system logger: optarg:syslog load_info ItemValue = off LoadConfFileString:key=[ad_dns] not found in /etc/melco/info. LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info. Starting kernel logger: ===== exec:inetd.sh ===== Starting inetd:===== exec:kernelmon.sh ===== Starting kernelmon:===== exec:miconmon.sh ===== miconmon 1.00b3 started (Builddate Feb 13 2007 19:24:56) ===== exec:mount_share.sh ===== /sbin/hotplug [block] share ===== exec:diskmon.sh ===== diskmon ver.1.01 f_type=0xef53 total_size=488809263104 free_byes=463771463680 ===== exec:errormon.sh ===== Starting errormon:errormon ver.1.00b5(BuildDate Jul 5 2007 21:47:04) Started ===== exec:hotplug.sh ===== ls: /proc/scsi/usb-storage/: No such file or directory ===== exec:ups ===== ** step3 ** ===== exec:micon_setup.sh ===== updating DHCP lease info: eth0 DHCPCSTATE=new ===== exec:atalk.sh ===== Starting AppleTalk services: configure atalkd atalk_name=LS-GL8F3 optarg:atalk load_info ItemValue = off LoadConfFileString:key=[ad_dns] not found in /etc/melco/info. LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info. file:/etc/atalk/AppleVolumes.default file:/etc/pam.d/netatalk file:/etc/atalk/afpd.conf (backgrounded) ===== exec:ftpd.sh ===== ftp is OFF ===== exec:httpd.sh ===== start Starting HTTPD services: /sbin/hotplug [module] /sbin/hotplug [module] /sbin/hotplug [module] /usr/local/apache/bin/apachectl start: httpd started ===== exec:smb.sh ===== Starting SMB services: configure samba optarg:samba load_info ItemValue = off LoadConfFileString:key=[ad_dns] not found in /etc/melco/info. LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info. LoadConfFileString:key=[msdfs_function] not found in /etc/melco/msdfs. LoadConfFileString:key=[msdfs_root_as_link] not found in /etc/melco/msdfs. LoadConfFileString:key=[msdfs_root_name] not found in /etc/melco/msdfs. LoadConfFileString:key=[msdfs_root_path] not found in /etc/melco/msdfs. LoadConfFileString:key=[msdfs_link1_name] not found in /etc/melco/msdfs. Can't Open : /etc/melco/offlinefile Can't Open : /etc/melco/shareinfo.hidden Can't Open : /etc/melco/shareinfo.vfs file:/etc/samba/smb.conf >IconvCodeCharset CodePage=0,charset=CP932 file:/etc/pam_smb.conf Starting NMB services: ===== exec:clientUtil_servd.sh ===== Starting clientUtil_server:starting on eth0 ===== exec:lsprcvd.sh ===== Starting lsprcvd:===== exec:daemonwatch.sh ===== Starting daemonwatch:daemonwatch Ver.1.01 watch list file : /etc/daemonwatch.list ===== exec:cron.sh ===== Start services: crond===== exec:logchkd.sh ===== Starting logchkd:logchkd ver.1.12(May 8 2007) started ===== exec:checkconfig.sh ===== ===== exec:bootcomplete.sh ===== /etc/init.d/bootcomplete.sh: line 44: flushqueue: command not found Starting pid 887, console /dev/ttyS0: '/sbin/getty' BUFFALO INC. LinkStation series LS-GL(IESADA) LS-GL8F3 login: /sbin/hotplug [block] XFS mounting filesystem sda6 /sbin/hotplug [block] BUFFALO INC. LinkStation series LS-GL(IESADA) LS-GL8F3 login: